Spec Disk 1998 Spring 4.0/Spec Disk 1998 Spring 4.0.iso/text/08842sol.txt

Text File | 1998-06-22 | 16.8 KB | 414 lines

                         SECTION 08842

                    LAMINATED GLASS GLAZING

NOTE ** Solutia, Inc., laminated glass and glazing.
NOTE **
NOTE ** This section is based on the products of Solutia,
        Inc., which is located at:
NOTE **    10300 Olive Boulevard
NOTE **    P.O. Box 66760
NOTE **    St. Louis, MO  63166-6760
NOTE **    Tel:  [phone]
NOTE **    Tel:  [phone]
NOTE **    Fax:  [phone]
NOTE **    Internet:  www.saflex.com
NOTE **
NOTE ** Solutia, Inc. produces Saflex(R) Interlayer, a
        plasticized polyvinyl butyral (PVB), which is used
        as the strengthening layer between plies of glass
        to produce laminated glass.
NOTE **
NOTE ** SECTION 08842 - LAMINATED GLASS GLAZING, Copyright
        1998, The Architect's Catalog, Inc.

PART 1  GENERAL

1.1 SECTION INCLUDES
NOTE ** Select paragraphs below applicable to project.
        Laminated glass manufactured with 0.015 inch PVB
        interlayer meets Category I tests of the Consumer
        Product Safety Commission, Federal Standard 16CFR
        1201.  Laminated glass manufactured with 0.030 inch
        PVB interlayer meets Category I and II tests of the
        Consumer Product Safety Standard.  Both laminated
        products comply with ANSI Z97.1.
NOTE **
NOTE ** Any glazing greater than 9 square feet (0.836
        square m) intended for use in shower, tub, or patio
        door assembly must be certified to comply with
        Category II.

    A.  Flat laminated glass, CPS Category I.

    B.  Flat laminated glass, CPS Categories I and II.

    C.  ______________________________________.

1.2 RELATED SECTIONS
NOTE ** Delete sections below not relevant to this project;
        add others as required.

    A.  Section 07900 - Joint Sealers.

    B.  Section 08100 - Metal Doors and Frames.

    C.  Section 08200 - Wood and Plastic Doors.

    D.  Section 08520 - Aluminum Windows.

    E.  Section 08600 - Skylights.

    F.  Section 08800 - Glazing.

    G.  Section 08910 - Metal-Framed Curtain Wall.

    H.  Section 10185 - Shower and Dressing Compartments.

    I.  Section 13125 - Greenhouses.

    J.  ______________________________________.

1.3 REFERENCES
NOTE ** Delete references from the list below that are not
        actually required by the text of the edited
        section; add others as required.

    A.  ANSI Z97.1 - American National Standard for Glazing
        Materials Used in Buildings -- Safety Performance
        Specifications and Methods of Test.

    B.  ASTM C 1036 - Specification for Flat Glass.

    C.  ASTM E 1300 - Practice for Determining the Minimum
        Thickness and Type of Glass Required to Resist a
        Specified Load.

    D.  ASTM F 1233 - Test Method for Security Glazing Material
        and Systems.

    E.  Consumer Product Safety Commission, Federal Standard
        16CFR1201.

    F.  UL 752 - Standard for Bullet-Resisting Equipment.

    G.  UL 972 - Standard for Burglary Resisting Glazing
        Material.

    H.  ___________________________________.


PART 2  PRODUCTS

2.1 MANUFACTURERS

    A.  Acceptable Interlayer Manufacturer:  Solutia, Inc., 10300
        Olive Boulevard, P.O. Box 66760, St. Louis, MO  63166-
        6760; ASD. Tel: [phone] or [phone]; Fax:
        [phone]; Internet:  www.saflex.com
NOTE ** Contact Glass Association of North America,
        Laminating Division, 3310 SW Harrison Street,
        Topeka, KS 66661-2279; Tel: [phone], for a
        list of member companies which could be included
        below.

    B.  Acceptable Laminated Glass Manufacturers:
        ____________________________________________________.

    C.  Requests for substitutions will be considered in
        accordance with provisions of Section 01600.
NOTE ** Delete paragraph above or below; coordinate with
        Division 1 requirements.

    D.  Substitutions:   Not permitted.

    E.  Provide all laminated glass from a single manufacturer.

2.2 MATERIALS
NOTE ** Glass and interlayer combinations are available in
        a wide range of colors and transmissions.  Cost and
        availability will depend on the specific color and
        transmission selected.

    A.  Interlayer:  Plasticized polyvinyl butyral (PVB).
NOTE ** Select PVB thickness and color below; delete those
        not required for the project.  As an alternative,
        when several types of laminated glass are required,
        delete thickness and color designations below and
        specify under the applications in Article 2.3,
        below.
        1.  Thickness:  0.015 inches (0.38 mm).
        2.  Thickness:  0.030 inches (0.76 mm).
        3.  Thickness:  0.060 inches (1.52 mm).
        4.  Thickness:  0.090 inches (2.28 mm).
        5.  Color:  Clear.
        6.  Color:  Bronze, Light.
        7.  Color:  Bronze, Medium.
        8.  Color:  Bronze, Dark.
        9.  Color:  Gray.
        10. Color:  Blue Green.
        11. Color:  Neutral Brown, Light.
        12. Color:  Neutral Brown, Medium.
        13. Color:  Neutral Brown, Dark.
        14. Color:  Translucent White.
NOTE ** Select type(s) of glass below; delete those not
        required for the project.  As an alternative, when
        several types of laminated glass are required,
        delete glass types below and specify under the
        applications in Article 2.3, below.

    B.  Glass:  Conforming to ASTM C 1036.
        1.  Annealed.
        2.  Tempered.
        3.  Heat-strengthened.
        4.  Chemically-strengthened.
        5.  Spandrel.
        6.  Tinted.
        7.  Reflective.
        8.  One-way mirror.
        9.  Two-way mirror.
        10. Clear bent.
        11. Tinted bent.
        12. Reflective bent.
        13. Wired.

2.3 LAMINATED GLASS
NOTE ** Design charts in ASTM E 1300 are used to select the
        proper thickness of laminated glass subject to wind
        and snow loads.  The procedure involves checking
        the strength of a trial laminated glass design
        against the design load which has been determined
        by the Architect or obtained from applicable
        building codes.

    A.  Provide laminated glass comprised of two or more pieces
        of glass and one or more interlayers, permanently bonded
        together under heat and pressure.
NOTE ** Select applications for laminated glass from
        paragraphs below, adding others as required for the
        project.  Delete applications not required; delete
        insignificant properties within each application.

    B.  Entrance Doors:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    C.  Sliding Doors:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    D.  Shower and Tub Enclosure Doors:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    E.  Storm Doors:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    F.  Sidelights:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    G.  Fixed Glass Panels:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    H.  Vision and Spandrel Areas:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    I.  Greenhouses:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    J.  Skylights:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    K.  Sloped Glazing:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    L.  Burglar-Resistant Glazing:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    M.  Bullet-Resistant Glazing:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    N.  Blast-Resistant Glazing:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.

    O.  _________________________________:
        1.  Glass Type:  _________________________________.
        2.  Glass Thickness:  _______ inches (______ mm).
        3.  Pieces of Glass:  _______.
        4.  Interlayer Thickness:  _______ inches (______ mm).
        5.  Interlayer Color:  _____________________.
        6.  Number of Interlayers:  _____.
        7.  Overall Thickness:  _______ inches (______ mm).
        8.  STC Value:  ___________.
        9.  Visible Light Transmittance:  ________ percent.
        10. Solar Optical Transmittance:  ________ percent.
        11. Properties Shading Coefficient:  _________.
        12. Design Instantaneous Heat Gain:  _______ BTUH/sq. ft.


PART 3  EXECUTION

3.1 EXAMINATION

    A.  Inspect and verify that frame openings are correct size
        and conform to recommendations of the glazing
        manufacturer.

3.2 PREPARATION

    A.  Clean frame contact surfaces with compatible solvent and
        wipe dry.  Do not allow solvent to pool in glazing
        channels.

3.3 INSTALLATION

    A.  Install laminated glass in accordance with manufacturer's
        recommendations for edge engagement and expansion
        allowance.

    B.  Employ only sealants and glazing accessories that have
        been approved by laminated glass manufacturer.


                         END OF SECTION